普通的開榫機設備,，由于自身的局限性,，每次由人工控制只能加工一根木料,，加工效率比較低,。如果要調整榫頭尺寸,，更換鋸片等操作也是比較麻煩,，也比較浪費時間,，榫頭的加工精度誤差比較大,。

相對于普通的設備,，數控開榫機就有很大的優勢。設備采用雙工位設計,，可以交替輪流工作,，這就大大提高了加工效率，每次加工榫頭的時間也縮短至8秒,。對于工人也沒有技術要求,，只需要工人上下料就可，非常的簡單方便,，降低了勞動強度,。無形當中就節省了大量的人工,，實現了批量化生產。在質量方面,，數控設備也有很好的表現,，精度一般可以達到10絲之內，這對于家具的生產來說完全可以滿足加工要求,。

一,、數控開榫機加工參數：

1.  可開榫頭：方榫、圓榫,、橢圓榫,、斜榫、豎榫,、腰圓榫

2.  圓榫較大加工尺寸：100mm

3.  常規加工尺寸：140X90mm

4.  運行功率：2.2KW

5.  主軸轉速：8000r/min

二：操作加工

1.檢查刀具,，接通電源，待機器運轉正常后開始作業,；

2.提前準備好要加工的木料,，將加工木料放在機器平臺上，按下氣動開關,，待夾緊木料后,，向前勻速推進，加工完成后拉回,，松開氣動開關,，取出木料；

3.按照要求加工一組,，加工完成后檢查榫頭尺寸是否符合加工要求,，并進行框試組，合格后再批量作業,；

4.在加工過程中要做好安全工作,，手不接近刀具，每二小時清掃一次現場,。

5.作業結束,，切斷電源，清掃現場,，并做好當班工作記錄,。

智拓?cái)?shù)控全力滿足客戶的需求，售后服務好,，客戶回購率高,。歡迎前來咨詢。

Ordinary tenoning machine equipment, due to its own limitations, each time by manual control can only process one wood, processing efficiency is relatively low. If you want to adjust the size of the tenon, replace the saw blade and other operations are more troublesome, but also a waste of time, and the processing accuracy error of the tenon is relatively large.

Compared with ordinary equipment, CNC tenoning machine has great advantages. The equipment adopts dual station design, which can work alternately, which greatly improves the processing efficiency, and the time of each processing tenon is shortened to 8 seconds. There are no technical requirements for workers, only workers can be loaded and unloaded, very simple and convenient, reducing labor intensity. It saves a lot of labor and realizes mass production. In terms of quality, CNC equipment also has a good performance, the accuracy can generally reach 10 wires, which can fully meet the processing requirements for the production of furniture. 

First, CNC tenon machining parameters:

1,、Can open tenon: square tenon, round tenon, oval tenon, oblique tenon, vertical tenon, waist tenon 

2. Round tenon large processing size: 100mm 

3. Conventional processing size: 140X90mm 

4. Operating power: 2.2KW4

5. Spindle speed: 8000r/min

Two: operation processing 

1,、Check the tool, turn on the power, and start the operation after the machine runs normally; 

2. Prepare the wood to be processed in advance, put the processed wood on the machine platform, press the pneumatic switch, push forward at a uniform speed after clamping the wood, pull back after processing, loosen the pneumatic switch, and remove the wood; 

3. Process a group according to the requirements, check whether the size of the tenon meets the processing requirements after the processing is completed, and carry out the frame test group, and then batch operation after passing; 

4. In the process of processing to do a good job of safety, the hand is not close to the tool, every two hours to clean the scene. 

5. After the operation, cut off the power supply, clean the site, and make a good record of work on duty. 

Zhituo CNC to meet the needs of customers, good after-sales service, customer repurchase rate is high. Welcome to inquire.